Fish Tackles and gear maintenance-an amateur’s guide, so stop buying new fishing gears regularly
Keeping up with the maintenance of your fishing tackle is not only a terrific method to save some cash but also gives you an excuse to routinely purchase new fishing equipment. You need to maintain your tackle if you want it to last for a longer period of time and have a higher value when you decide to sell it. When an angler is fishing, their gear is exposed to some of the most corrosive elements that Mother Nature has to offer, including air, water, salt, sun, and wind. However, there are a few easy things that you can do that will improve the protection of your fishing equipment and lessen the likelihood of it breaking down.
Tackle care
- When you go fishing, you should do your best to limit the amount of time that the fishing rods and reels are exposed to elements such as sand and salt water. That does not insulate them or wrap protective material over them; nevertheless, it does guarantee that you don’t drop them in the ocean or leave them unattended where they may be exposed to the sea sprays, tides, and winds. If salt water gets into the deeper parts of your reel, this might prove to be deadly.
- Even if it is not feasible to completely protect your fishing rods and reels from the weather, you should always make sure to use warm soapy water and carefully sponge off your gear. This will remove any sand or salt particles that may have gotten into the equipment. After washing the tackle, you should dry it with a piece of towel and then spin the handle to shake out any water that may have accumulated in the working components.
- Make use of a light aerosol lubricant or a corrosion inhibiting spray and spray it all over the body of the tackle. After a few minutes, wipe it off and you should be good to go. Inox is the most effective corrosion inhibitor that the specialists suggest using. It is best to let it dry out entirely in the open air rather than keeping it trapped in a container or your fishing gear since this might slow down the drying process.
- In addition, take care not to bang your fishing rods on board decks, rocks, or any other hard things, since this may cause the reel’s frame or the internal components to get damaged.
- Additionally, if you want to be extra cautious, you can certainly send your tackle in for service once a year to guarantee that the internal components are in excellent condition and will function appropriately.
Gears care
If you intend to completely disassemble your fishing rods and reels in order to clean and lubricate them, you should make sure that the separated equipment is kept on a piece of paper or a clean cloth. This allows us to more easily recall our progress and even demarcate them as to where they will fit once assembling begins.
Lubrication should be applied in accordance with the specifications provided by the manufacturer. If at all possible, avoid using petroleum jelly, since this may cause your reel to get stiff or even shut down completely. It is important to make use of lubricants that are designed specifically for use on individual components of fishing rods and reels. It’s possible that the lube on a reel that’s meant to be used for lubricating the teeth won’t work well as a grease lubricant.
When working with gears, it is imperative that viscous liquids such as reel grease be used at all times. This allows the gears to be held securely in place. In addition, make sure that the fishing rods are covered while they are not being used by utilizing reel covers and reel bags.
Line Roller care
The line roller is what makes it possible for the line to unwind itself from the reel as a run progresses. Because rolling is in the name of the ability, having the skill is a prerequisite. On the other hand, its capacity for rolling smoothly will be hindered by dirt that has collected as a consequence of several retrievals. Maintaining its cleanliness needs regular maintenance, which may be performed via the use of the following straightforward approaches. Check the schematics that were included with your reel in the event that you have a different kind of reel. There isn’t a huge gap between the individual parts and the final product when put together. It is quite important to have the schematic for your reel close at hand if you are doing any type of maintenance.
- Loosen the screw that is responsible for holding the line roller in place, and then repeat the previous step.
- To remove the arm of the bail from the bail, just press the arm in the opposite direction of the bail.
- Keep a close eye out for any little, fragile items that could fall.
- Rearrange the components such that they are still in the same order as when they were taken out. When putting things back together, this will prove to be really helpful.
- To properly clean and lubricate the component, use the image that may be seen below as a reference.
- The housing of the line roller is yet another popular location for the accumulation of dirt and debris. When you are done, you should put everything back together.
- Check to see that the screw that was visible in step one is not screwed in too tightly.
- The very last thing that has to be done is checking to see whether the roller can freely spin on its axis.
- Utilize a toothpick to assist you in using the roller when working in bright light by moving it vertically up and down.
- If it moves in the expected direction, then everything is in order, and you may go on. If it doesn’t, don’t commit suicide.
- It is sufficient to check the screws a second time to ensure that they have the appropriate amount of torque, and to examine the assembly for any flaws.
